Delamination formation and suppression during rotary ultrasonic elliptical machining of CFRP, Compos B, vol.183, p.107698, 2020. ,
Threedimensional oblique cutting model for sub-surface damage analysis in CFRP/Ti stack composite machining, Int J Adv Manuf Technol, vol.96, pp.643-655, 2018. ,
Drilling temperature and hole quality in drilling of CFRP/aluminum stacks using diamond coated drill, Int J Precis Eng Manuf, vol.16, issue.8, pp.1689-1697, 2015. ,
Introduction: engineering requirements for aerospace composite materials, 2015. ,
Experimental analysis of the influence of drill point angle and wear on the drilling of woven CFRPs, Materials, vol.7, pp.4258-4271, 2014. ,
Influence of machining parameters and tool structure on cutting force and hole wall damage in drilling CFRP with stepped drills, Int J Adv Manuf Technol, vol.97, pp.857-865, 2018. ,
Study on tool wear and work piece surface integrity following drilling of CFRP laminates with variable feed rate strategy, Sci Direct Proc CIRP, vol.71, pp.407-412, 2018. ,
Experimental investigation of drilling damage and stitching effects on the mechanical behavior of carbon/epoxy composites, Int J Mach Tools Manuf, vol.87, pp.61-72, 2014. ,
URL : https://hal.archives-ouvertes.fr/hal-02126040
Experimental effect of cutting parameters and tool geometry in drilling woven CFRP, advances in mechanical engineering and mechanics. CoTuMe 2018. Lecture notes in mechanical engineering, 2019. ,
Advanced composite materials of the future in aerospace industry, INCAS BULLETIN, vol.5, issue.3, pp.139-150, 2013. ,
A novel prediction model for thrust force and torque in drilling interface region of CFRP/Ti stacks, Int J Adv Manuf Technol, vol.81, pp.1497-1508, 2014. ,
Experimental investigation on mechanical drilling of a newly developed CFRP/Al co-cured material, Int J Adv Manuf Technol, vol.106, pp.993-1004, 2019. ,
On full life-cycle instantaneous force predicting when drilling CFRP-metal stacks, Int J Adv Manuf Technol, vol.88, pp.651-661, 2016. ,
Tool Wear mechanism in cutting of stack CFRP/UNS A97075, Materials, vol.11, p.1276, 2018. ,
Effects of twist drill geometry and drilling parameters on CFRP-aluminum stack up in single shot drilling, SciFed J Mater Res Lett, vol.2, issue.2, pp.1-14, 2018. ,
Tool geometry optimization for drilling CFRP/Al-Li stacks with a lightning strike protection, AIP Conference Proc, vol.1896, p.90009, 2017. ,
Effect of tool geometry and cutting parameters on delamination and thrust forces in drilling CFRP/Al-Li, AIP Conference Proc, vol.1769, p.80012, 2016. ,
Study on thrust force and torque sensor signals in drilling of Al/CFRP stacks for aeronautical applications, 12th CIRP Conference on Intelligent Computation in Manufacturing Engineering, vol.79, pp.337-342, 2018. ,
Characterization of hole quality and temperature in drilling of Al/CFRP stacks under different process condition, 12th CIRP Conference on Intelligent Computation in Manufacturing Engineering, vol.79, pp.319-324, 2018. ,
Multi response prediction of cutting force and delamination in carbon Fiber reinforced polymer using backpropagation neural network-genetic algorithm, AIP Conference Proceedings 2114, p.30012, 2019. ,
Drilling optimization of woven CFRP laminates under different tool wear conditions: a multi-objective design of experiments approach, Struct Multidiscip Optim, vol.53, pp.239-251, 2015. ,
Embedded electronics influence on the strength of carbon fiber laminate, Adv Mater Res, vol.905, pp.239-243, 2014. ,
Modelling a new composite from a recycled GFRP, Mechanics of Composite Materials, vol.44, issue.6, 2008. ,
Performance evaluation of carbide tools in drilling CFRP-Al stacks, J Compos Mater, vol.48, issue.17, pp.2071-2084, 2014. ,
Drilling of composites and resulting surface integrity, CIRP Annals Manuf Technol, vol.60, pp.57-60, 2011. ,
Acoustic emission as a tool for identifying drill position in fiber-reinforced plastic and aluminum stacks, Int J Mach Tools Manuf, vol.57, pp.20-26, 2012. ,
Tool wear in drilling of composite/titanium stacks using carbide and polycrystalline diamond tools, Wear, vol.271, pp.2826-2835, 2011. ,
Study of drilling of composite material and aluminum stack, Compos Struct, vol.92, pp.1246-1255, 2010. ,
Method of hole shrinkage radial forces measurement in Ti6Al4V drilling, 16 th CIRP Conference on Modelling of Machining Operations, vol.58, pp.629-634, 2017. ,
URL : https://hal.archives-ouvertes.fr/hal-01548629
Influence of cutting forces and damage on 2D and 3D carbon/epoxy composites in drilling, Key Eng Mater, pp.1217-1225, 2014. ,
Acoustic emission for controlling drill position in fiber-reinforced plastic and metal stacks, CIRP Ann Manuf Technol, vol.61, pp.75-78, 2012. ,
Etude du processus de délaminage mode I, mode II et mode mixte (I+II) de matériaux composites à renforts tissés à différentes vitesses de sollicitation, 1993. ,
Formation of interlayer gap and control of interlayer burr in dry drilling of stacked aluminum alloy plates, Chin J Aeronaut, vol.19, issue.1, pp.283-291, 2016. ,
Burr and cap formation by orbital Drilling of Aluminum, proceedings of the CIRP international conference on burrs, pp.31-44, 2009. ,
The drilling of carbon fiber composite-aluminum stacks and its effect on hole quality and integrity, proceedings of the institution of mechanical engineers, Part B: Journal of Engineering Manufacture, pp.1-9, 2017. ,
Influence of point angle on drill hole quality and machining forces when drilling CFRP, science direct, 5th CIRP conference on high performance cutting, pp.471-476, 2012. ,
Machining of Al/SiC particulate metal matrix composites part II: workpiece surface integrity, J Mater Process Technol, vol.83, pp.277-285, 1998. ,
Experimental studies on the performance of different structure tools in drilling CFRP/Al alloy stacks, Int J Adv Manuf Technol, vol.81, pp.241-251, 2015. ,
Evaluating hole quality in drilling of Al 6061 alloys, Materials, vol.11, p.2443, 2018. ,
Experimental study on mechanical drilling of carbon / epoxy composite -Ti6Al4V stacks, 2019. ,
Experimental study of surface quality and damage when drilling unidirectional CFRP composites, J Mater Res Technol, vol.3, issue.4, pp.354-362, 2014. ,
, Publisher's note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations