R. Zitoune, V. Krishnaraj, S. Almabouacif, B. Collombet, F. Sima et al., Influence of machining parameters and new nano-coated tool on drilling performance of CFRP/Aluminium sandwich, Compos Part B Eng, vol.43, pp.1480-1488, 2012.
URL : https://hal.archives-ouvertes.fr/hal-02185577

N. Cadorin, R. Zitoune, P. Seitier, and F. Collombet, Analysis of damage mechanism and tool wear while drilling of 3D woven composite materials using internal and external cutting fluid, J Compos Mater, vol.49, pp.2687-703, 2015.

A. Hejjaji, D. Singh, S. Kubher, D. Kalyanasundaram, and S. Gururaja, Machining damage in FRPs: Laser versus conventional drilling, Compos Part A Appl Sci Manuf, vol.82, pp.42-52, 2016.

M. Haddad, R. Zitoune, F. Eyma, and B. Castanié, Machinability and surface quality during high speed trimming of multi directional CFRP, Int J Mach Mach Mater, 2013.
URL : https://hal.archives-ouvertes.fr/hal-02078611

R. Prakash, V. Krishnaraj, R. Zitoune, and J. Sheikh-ahmad, High-speed edge trimming of CFRP and online monitoring of performance of router tools using acoustic emission, vol.9, 2016.
URL : https://hal.archives-ouvertes.fr/hal-01950772

M. Slamani, J. Chatelain, and H. Hamedanianpour, Influence of machining parameters on surface quality during high speed edge trimming of carbon fiber reinforced polymers, Int J Mater Form, 2018.

H. Wang, J. Sun, D. Zhang, K. Guo, and J. Li, The effect of cutting temperature in milling of carbon fiber reinforced polymer composites, Compos Part A Appl Sci Manuf, vol.91, pp.380-387, 2016.

F. Wang, J. Yin, Z. Jia, B. Niu, and W. Liu, A novel approach to evaluate the delamination extent after edge trimming of carbon-fiber-reinforced composites, Proc Inst Mech Eng Part B J Eng Manuf, 2017.

N. Nguyen-dinh, R. Zitoune, C. Bouvet, and S. Leroux, Surface integrity while trimming of composite structures : X-ray tomography analysis, Compos Struct, vol.210, pp.735-781, 2019.
URL : https://hal.archives-ouvertes.fr/hal-01969389

D. H. Wang, M. Ramulu, and D. Arola, Orthogonal cutting mechanisms of graphite/epoxy composite. Part I: unidirectional laminate, Int J Mach Tools Manuf, 1995.

R. Zitoune, F. Collombet, F. Lachaud, R. Piquet, and P. Pasquet, Experiment-calculation comparison of the cutting conditions representative of the long fiber composite drilling phase, Compos Sci Technol, vol.65, pp.455-66, 2005.

A. Koplev, A. Lystrup, and T. Vorm, The cutting process, chips, and cutting forces in machining CFRP, Composites, vol.14, issue.83, p.90157, 1983.

D. H. Wang, M. Ramulu, and D. Arola, Orthogonal cutting mechanisms of graphite/epoxy composite. Part II: multi-directional laminate, Int J Mach Tools Manuf, vol.35, issue.12, pp.1639-1687, 1995.

M. Ramulu and J. Kramlich, Machining of fiber reinforced composites: Review of environmental and health effects, Int J Environ Conscious Des Manuf, vol.11, pp.1-19, 2004.

, Standardization EC for. Workplace atmospheres -Sizefraction definitions for measurement of airborne particles, Br Stand, pp.1-15, 1993.

J. Wagman, Dusts and residues from machining and incinerating graphite/epoxy composites: a preliminary study, Environ Technol Lett, vol.3, pp.469-78, 1982.

E. S. Boatman, D. Covert, D. Kalman, D. Luchtel, and G. S. Omenn, Physical, morphological, and chemical studies of dusts derived from the machining of composite-epoxy materials, Environ Res, vol.45, pp.80050-80051, 1988.

J. L. Miller and M. Tuttle, Investigation of machinability and dust emissions in edge trimming of laminated carbon fiber, Composites, 2014.

M. Haddad, R. Zitoune, F. Eyma, and B. Castanie, Study of the surface defects and dust generated during trimming of CFRP: Influence of tool geometry, machining parameters and cutting speed range, Compos Part A Appl Sci Manuf, 2014.
URL : https://hal.archives-ouvertes.fr/hal-01952583

J. Y. Sheikh-ahmad, Machining Polym Compos, 2009.

F. Klocke, C. Koenig, C. Wuertz, and C. D. , Environmental Effects and Safety in Machining Fibrous Composites.pdf, pp.411-436, 1999.

A. K. Iyer, Characterization of composite dust generated during milling of uni-directional and random fiber, Composites, 2015.

A. Hejjaji, R. Zitoune, L. Crouzeix, and F. Collombet, Influence of controlled depth abrasive water jet milling on the fatigue behavior of carbon/epoxy composites, Compos. Part A: Appl. Sci. Manufact, vol.121, pp.397-410, 2019.
URL : https://hal.archives-ouvertes.fr/hal-02134037

A. Hejjaji, R. Zitoune, L. Crouzeix, S. Le, and F. Collombet, Surface and machining induced damage characterization of abrasive water jet milled carbon/epoxy composite specimens and their impact on tensile behavior, Wear, pp.1356-64, 2017.
URL : https://hal.archives-ouvertes.fr/hal-01620031

J. Y. Sheikh-ahmad, F. Almaskari, and F. Hafeez, Thermal aspects in machining CFRPs: effect of cutter type and cutting parameters, Int J Adv Manuf Technol, vol.100, pp.2569-82, 2019.