M. J. Philippe, E. Bouzy, and J. J. Fundenberger, Textures and anisotropy of titanium alloys, Mater. Sci. Forum, vol.273, issue.275, pp.511-522, 1998.

G. Gilles, W. Hammami, V. Libertiaux, O. Cazacu, J. Yoon et al., Experimental characterization and elasto-plastic modeling of the quasi-static mechanical response of TA6V at room temperature, Solids Struct, vol.48, pp.1277-1289, 2011.

W. Tirry, F. Coghe, S. Bouvier, M. Gasperini, L. Rabet et al., A multiscale characterization of deformation twins in Ti-6Al-4V sheet material deformed by simple shear, Mater. Sci. Eng. A, vol.527, pp.4136-4145, 2010.

J. A. Medina-perilla and J. G. Sevillano, Two-dimensional sections of the yield locus of a Ti-6Al-4V alloy with a strong transverse_type crystallographic a-texture, Mater. Sci. Eng. A, vol.201, pp.103-110, 1995.

F. Bridier, P. Villechaise, and J. Mendez, Analysis of the different slip systems activated by tension in a ? titanium alloy in relation with local crystallographic orientation, Acta Mater, vol.53, pp.555-567, 2005.

D. Dunst and H. Mecking, Analysis of experimental and theoretical rolling textures of two-phase titanium alloys, Z. Met.kd, vol.87, pp.498-507, 1996.

A. Salem, S. Kalidindi, and R. D. Doherty, Strain hardening of titanium: Role of deformation twinning, Acta Mater, vol.51, pp.4225-4237, 2003.

S. Zaefferer, A study of active deformation systems in titanium alloys: Dependence on alloy composition and correlation with deformation texture, Mater. Sci. Eng. A, vol.344, pp.20-30, 2003.

M. Nixon, O. Cazacu, and R. Lebensohn, Anisotropic response of high-puritytitanium: Experimental characterization and constitutive modeling, Int. J. Plast, vol.26, pp.516-532, 2010.

D. Lunt, Q. D. Fonseca, D. Rugg, and M. Preuss, Microscopic strain localisation in Ti-6Al-4V during uniaxial tensile loading, Mater. Sci. Eng. A, vol.680, pp.444-453, 2017.

H. Fan, S. Aubry, A. Arsenlis, and J. A. El-awady, Orientation influence on grain size effects in ultrafine-grained magnesium, Scr. Mater, vol.97, pp.25-28, 2015.

W. L. Wang, X. L. Wang, W. Mei, and J. Sun, Role of grain size in tensile behavior in twinning-induced Ti-20V-2Nb-2Zr alloy, Mater. Charact, vol.120, pp.263-267, 2016.

E. Arzt, Size effects in materials due to microstructural and dimensional constraints: A comparative review, Acta Mater, vol.46, pp.5611-5984, 1998.

I. J. Beyerlein, L. Capolungo, P. E. Marshall, R. J. Mccabe, and C. N. Tome, Statistical analyses of deformation twinning in magnesium, Phil. Mag, vol.90, pp.2161-2190, 2010.

A. Fernández, A. Jérusalem, I. Gutiérrez-urrutia, and M. T. Pérez-prado, Threedimensional investigation of grain boundary-twin interactions in a Mg AZ31 alloy by electron backscatter diffraction and continuum modeling, Acta Mater, vol.61, pp.7679-7692, 2013.

E. O. Hall, The deformation and ageing of mild steel: III discussion of results, Proc. Phys. Soc. B, vol.64, pp.747-753, 1951.

N. J. Petch, The cleavage strength of polycrystals, J. Iron Steel Inst, vol.174, pp.25-28, 1953.

H. Li, D. E. Mason, T. R. Bieler, C. J. Boelert, and M. A. Crimp, Methodology for estimating the critical resolved shear stress ratios of -phase Ti using EBSD-based trace analysis, Acta Mater, vol.61, pp.7555-7567, 2013.

J. R. Mayeur and D. L. Mcdowell, A three-dimensional crystal model for duplex Ti-6Al-4V, Int. J. Plast, vol.23, pp.1457-1485, 2007.

S. L. Semiatin and T. R. Bieler, The effect of alpha platelet thickness on plastic flow during hot working of Ti-6Al-4V with a transformed microstructure, Acta Mater, vol.49, pp.3565-3573, 2001.

R. Armstrong, I. Codd, R. M. Douthwaite, and N. J. Petch, The plastic deformation of polycrystalline aggregates, Phil. Mag. A, J. Theor. Exp. Appl. Phys, pp.45-58, 1962.

L. Wang, Z. Zheng, H. Phukan, P. Kenesei, J. Park et al., Direct measurement of critical resolved shear stress of prismatic and basal slip in polycrystalline Ti using high energy X-ray diffraction microscopy, Acta Mater, vol.132, pp.598-610, 2017.

B. Raeisinia and S. R. Agnew, Using polycrystal plasticity modeling to determine the effects of grain size and solid solution additions on individual deformation mechanisms in cast Mg alloys, Scr. Mater, vol.63, pp.731-736, 2010.

C. M. Cepeda-jiménez, J. M. Molina-aldareguia, and M. T. Pérez-prado, Effect of grain size on slip activity in pure magnesium polycrystals, Acta Mater, vol.84, pp.443-456, 2015.

G. J. Weng, Microstructural theory of grain size dependance in metal plasticity, Int. J. Mech. Phys. Solids, vol.31, pp.193-203, 1983.

S. Berbenni, V. Favier, and M. Berveiller, Impact of the grain size distribution on the behaviour of heterogeneous materials, Int. J. Plast, vol.23, pp.114-142, 2007.

N. Nicaise, S. Berbenni, F. Wagner, M. Berveiller, and X. Lemoine, Coupled effects of grain size distributions and crystallographic textures on the plastic behaviour of IF steels, Int. J. Plast, vol.27, pp.232-249, 2011.

A. Jain, O. Duygulu, D. W. Brown, C. N. Tomé, and S. R. Agnew, Grain size effects on the tensile properties and deformation mechanisms of a magnesium alloy, AZ31B, sheet, Mater. Sci. Eng. A, vol.486, pp.545-555, 2008.

B. S. Fromm, B. L. Adams, S. Ahmadi, and M. Knezevic, Grain size and orientation distributions: Application to yielding of -titanium, Acta Mater, vol.57, pp.2339-2348, 2009.

B. Raeisinia, C. W. Sinclair, W. J. Poole, and C. N. Tome, On the impact of grain size distribution on the plastic behaviour of polycrystalline metals, Model. Simul. Sci. Eng, vol.16, p.25001, 2008.

B. D. Smith, D. Shih, and D. L. Mcdowell, Cyclic plasticity experiments and polycrystal plasticity modeling of three distinct Ti alloy microstructures, Int. J. Plast, vol.13, pp.1-23, 2018.

L. Méric, P. Poubanne, and G. Cailletaud, Single crystal modeling for structural calculations: Part 1-Model presentation, Eng. Mater. Technol, vol.113, pp.162-170, 1991.

M. Berveiller and A. Zaoui, An extension of the self-consistent scheme to plastically-flowing polycrystals, Mech. Phisycs Solids, vol.26, pp.325-344, 1978.

S. Hémery, P. Nizou, and P. Villechaise, In situ SEM investigation of slip transfer in Ti-6Al-4V: Effect of applied stress, Mater. Sci. Eng. A, vol.709, pp.277-284, 2018.

A. Nafi, M. Cheikh, and O. Mercier, Identification of mechanical properties of CuSilsteel brazed structures joints: A numerical approach, J. Adhes. Sci. Technol, vol.27, issue.24, pp.2705-2713, 2013.
URL : https://hal.archives-ouvertes.fr/hal-01687309

C. Frederick and P. Armstrong, A mathematical representation of the multiaxial bauschinger effect, Mater. High Temp, vol.24, pp.1-26, 2007.

T. Dick and G. Cailletaud, Fretting modelling with a crystal model of Ti6Al4V, Comput. Mater. Sci, vol.38, pp.113-125, 2006.
URL : https://hal.archives-ouvertes.fr/hal-00133520

M. Kasemer, M. L. Echlin, J. C. Stinville, T. M. Pollock, and P. Dawsona, On slip initiation in equiaxed ? Ti-6Al-4V, Acta Mater, vol.136, pp.288-302, 2017.

B. Barkia, V. Doquet, J. P. Couzinié, I. Guillot, and E. Héripré, In situ monitoring of the deformation mechanisms in titanium with different oxygen contents, Mater. Sci. Eng. A, vol.636, pp.91-102, 2015.
URL : https://hal.archives-ouvertes.fr/hal-01227185

D. H. Kohn and P. Ducheyne, Tensile and fatigue strength of hydrogen-treated Ti-6Al-4V alloy, Mater. Sci, vol.26, pp.328-334, 1991.

Z. X. Zhang, S. J. Qu, A. H. Feng, and J. Shen, Achieving grain refinement and enhanced mechanical properties in Ti-6Al-4V alloy produced by multidirectional isothermal forging, Mater. Sci. Eng. A, vol.692, pp.127-138, 2017.

S. Zherebtsov, E. Kudryavtsev, S. Kostjuchenko, S. Malysheva, and G. Salishcheva, Strength and ductility-related properties of ultrafine grained two-phase titanium alloy produced by warm multiaxial forging, Mater. Sci. Eng. A, vol.536, pp.190-196, 2012.

H. S. Kim, S. J. Yoo, J. W. Ahn, D. H. Kim, and W. J. Kim, Ultrafine grained titanium sheets with high strength and high corrosion resistance, Mater. Sci. Eng. A, vol.528, pp.8479-8485, 2011.

D. Rugg, M. Dixon, and F. P. Dunne, Effective structural unit size in titanium alloys, Strain Anal. Eng. Design, vol.42, pp.269-279, 2007.

M. G. Glavicic, B. B. Bartha, S. K. Jha, and C. J. Szczepanski, The origins of microtexture in duplex Ti alloys, Mater. Sci. Eng. A, pp.325-328, 2009.

L. Germain, N. Gey, M. Humbert, P. Bocher, and M. Jahazi, Analysis of sharp microtexture heterogeneities in a bimodal IMI 834 billet, Acta Mater, vol.53, pp.3535-3543, 2005.
URL : https://hal.archives-ouvertes.fr/hal-00111879

H. Conrad, Effect of interstitial solutes on the strength and ductility of titanium, vol.26, pp.123-403, 1981.

R. Lebensohn and G. Canova, A self-consistent approach for modelling texture development of two-phase polycrystals: Application to titanium alloys, Acta Mater, vol.45, pp.3687-3694, 1997.

N. E. Paton, J. C. Williams, and G. P. Rauscher, The deformation of -phase titanium, Titan. Sci. Technol, vol.1, pp.1049-1069, 1973.

M. J. Philippe, C. Esling, and B. Hochheid, Role of twinning in texture development and in plastic deformation of hexagonal materials, Textures Microstruct, vol.7, pp.265-301, 1988.

A. T. Churchman, The slip modes of titanium and the effect of purity on their occurrence during tensile deformation of single crystals, Math. Phys. Eng. Sci, vol.226, pp.216-224, 1954.

T. Sakai and M. Efine, Plastic deformation of Ti-Al single crystals in prismatic slip, Acta Metall, vol.22, pp.1359-1372, 1974.