Mechanics of sheet metal forming, 2002. ,
Sheet metal forming processes: constitutive modelling and numerical simulation, p.301, 2010. ,
Edition Springer, 2007. ,
Material saving and cost reduction with hot forming of a U-shaped titanium part, Materialwiss Werkst, vol.45, issue.9, pp.841-847, 2014. ,
Thermo-mechanical sheet metal forming of aero engine components in Ti-6Al-4V -Part 1: Material characterisation, Int J Mater Form, vol.6, issue.3, pp.391-402, 2013. ,
Superplasticity in Ti-6Al-4V: characterisation, modelling and applications, Acta Mater, vol.95, pp.428-470, 2015. ,
Behavior modeling and microstructural evolutions of Ti-6Al-4V alloy under hot forming conditions, Int J Mech Sci, 2016. ,
Ti-6Al-4V: deformation map and modelisation of tensile behaviour. Royal Military Academy -Katholieke Universiteit Leuven, 2007. ,
Experimental characterization and elasto-plastic modeling of the quasi-static mechanical response of TA-6V at room temperature, Int J Solids Struct, vol.48, issue.9, pp.1277-89, 2011. ,
Deep drawing of Ti6Al4V: experiments and modeling over a wide range of strain rates and temperatures, Key Eng Mater, pp.190-195, 2013. ,
URL : https://hal.archives-ouvertes.fr/hal-00847431
Mechanical behavior of Ti-6Al-4V at high and moderate temperatures -Part I: Experimental results, Mater Sci Eng A, vol.326, pp.1507-1513, 2002. ,
Dynamic response of conventional and hot isostatically pressed Ti-6Al-4V alloys: experiments and modeling, Mech Mater, vol.33, pp.63-64, 2001. ,
A theory of the yielding and plastic flow of anisotropic metals, Proc Royal Soc A, vol.193, pp.281-97, 1033. ,
A six-component yield function for anisotropic materials, Int J Plasticity, vol.7, issue.7, p.90052, 1991. ,
Orthotropic yield criterion for hexagonal closed packed metals, Int J Plasticity, vol.22, issue.7, pp.1171-94, 2006. ,
Material characterisation for analyses of titanium sheet metal forming. Luleå University of Technology, 2005. ,
Anisotropy and tensioncompression asymmetry modeling of the room temperature plastic response of Ti-6Al-4V, Int J Plasticity, vol.67, issue.1, pp.53-68, 2015. ,
A sigmoidal model for superplastic deformation, J Mater Des Appl, vol.219, issue.3, pp.149-62, 2005. ,
, Non-contracting measurement solutions, 2017.
Image correlation for shape, motion and deformation measurements, 2009. ,
URL : https://hal.archives-ouvertes.fr/hal-01729219
Anodic oxidation of titanium and its alloys, J Mater Sci, vol.8, issue.5, pp.688-704, 1973. ,
Smoothing and differentiation of data by simplified least squares procedures, Anal Chem, vol.36, issue.8, pp.1627-1666, 1964. ,
Emboutissage des tôles -Importance des modes de déformations, Techniques de l'ingénieur, vol.7510, pp.1-25, 2011. ,
Direct identification of a combined hardening with a cyclic bending test, 2005. ,
URL : https://hal.archives-ouvertes.fr/hal-00507227
International conference and workshop on numerical simulation of 3-D sheet metal forming processes, NUMISHEET '93, 1993. ,
Thermo-mechanical material response and hot sheet metal forming of Ti-6242, Mater Sci Eng A, vol.489, issue.1-2, pp.158-68, 2008. ,
Introduction to dislocations, 2011. ,
Mécanique des matériaux solides, 2009. ,
Experimental and theoretical investigation of forming limit diagram for Ti-6Al-4V alloy at warm condition, Int J Mater, vol.10, pp.255-66, 2017. ,
Formage incrémental de tôle d'aluminium: étude du procédé à l'aide de la mesure de champs et identification de modèles de comportement, Université Paul Sabatier -Toulouse, vol.3, 2009. ,
Polymorphic constitutive equations in finite element codes, Comput Methods Appl Mech Eng, vol.141, issue.96, pp.355-72, 1997. ,
Analyse et optimisation des procédés de formage de pièces en alliage de Titane. Université de recherche Paris Sciences et Lettres, 2016. ,
Tribological behaviors in titanium sheet and tube forming at elevated temperatures: evaluation and modeling, Int J Adv Manuf Technol, vol.97, issue.1, pp.657-74, 2018. ,
State-of-the-art of simulation of sheet metal forming, J Mater Process Technol, vol.103, pp.413-414, 2000. ,
Concepts and applications of finite element analysis. Edition Wiley, 2002. ,
Non-linear finite element analysis of solids and structures, 2000. ,
Building better products with finite element analysis. Edition Delmar, 1999. ,